Comments
-
Hi @ChrisLakeErie, Thank you for visiting SonicWall Community. The configuration on the below KB article is something that you are looking for. Please go through the same and it should match your requirement. Please feel free to post for any questions/clarification.
-
Hi @ENZINO78, Yes, the option is available to collect certain debug logs and not to completely use the GUI for management purpose. There is a alert notification next to the option.
-
Hi @Fearless_Freddy, Thank you for visiting SonicWall Community. Please create a NAT policy as mentioned below and check if it does the trick. This NAT policy is Source Translation NAT policy. Source: L2TP IP Pool Translated Source: X0 IP (select the address object of the SonicWall's LAN IP that is pingable from the L2TP…
-
Hi @BHO, Are you using any SonicWall Email Security physical appliance or Hosted appliance along with Cisco ASA firewall on your network? The usage of these domains will have effect only when any of the SonicWall appliances are present in the network as the appliances can try to load the latest definition from these…
-
Hi @DJHURT1, Thank you for visiting SonicWall Community. Both these KB's talk about the same scenario and the only difference is w.r.t the requirement. So, picking the configuration for tunnel interface VPN would be based on the need. If you have a simple or small network where there is no dynamic routing involved, you can…
-
Hi @RICHARDMCF, Does this affect all kind of traffics like Ping or RDP or Radiology application from the SSLVPN client? Best way to find the root cause is to perform a packet capture on the SonicWall.
-
Hi @FEARLESS_FREDDY, Thank you for visiting SonicWall Community. I can give couple of suggestions and ask you to check. Could you please try disabling windows firewall on the Internal Host were pings requests are getting forwarded to? Similarly, please turn of the Anti-Virus for testing if any on the Internal Host. Could…
-
Hi @CBACK85, Thank you for visiting SonicWall Community. Technically there shouldn't be any HA failover for adjusting the subnet mask on existing subnets. May I know which interface is gonna get adjusted for the subnet mask on SonicWall from /24 to /23? Please cross verify that you have access to the SonicWall while doing…
-
Hi @KARL, Thank you for visiting SonicWall Community. Please use below KB article link as a reference to configure the WAN interface on SonicWall as DHCP. You will have to enable the HTTPS slider under MANAGEMENT to manage the SonicWall using WAN IP. Since the WAN IP address is going to be DHCP and it changes randomly, it…
-
@MRSHAHIN - Leave the source and destination ports field empty. You can put the IP addresses in question to either source IP or destination IP address fields as per the scenario. If its outbound direction, capture the traffic based on destination IP and it its inbound direction, capture the traffic based on source IP…
-
Hi @BHO, Thank you for visiting SonicWall Community. Where do you see these domains used in the network? I meant on any appliance?
-
Hi @WALKMAN, Thank you so much for your response. Very happy to hear that the issue has been sorted out with the help of the suggested KB article. Hope you are all set with SonicWall. Please feel free to post us for any help or assistance with SonicWall products. Have a good one!!!
-
Hi @DALEWEST, Thank you for visiting SonicWall Community. Your understanding with Stealth Mode is right. Let me try to understand your firewall config. Which direction traffic are we talking about here? LAN to WAN or vice versa? Do you have appropriate access rules defined on the SonicWall to deny the traffic? Could you…
-
Hi @RICHARDMCF, Have you ensured Client Routes are configured with the appropriate LAN Subnets in the SSLVPN? This is also needed for the access to happen. Is this issue common to all SSLVPN users from various locations or to specific SSLVPN users? The best way to determine the root cause of the issue is to perform a…
-
Hi @DJHURT1, I see that you have a local DHCP server. In my previous comment, I have mentioned that "if you are planning to make the clients on the spoke to get IP address from the HUB SonicWall", so I missed noticing that you have a local DHCP server. In this case, yes you can do a IP Helper with Hub and Spoke scenario.…